Carryboy cargo area cover tarpaulin 743-FTD

NOVISauto care spray "TONNO TONIC"  for all luggage compartment covers and tarpaulins made of ABS hard plastic and vinyl. Tonno Tonic cares, cleans and gives your cover a fresh shine in a single step -  it effectively protects against UV light. Tonno Tonic has been thoroughly tested and is 100% suitable for protecting all ABS hard plastic and vinyl covers.  Remember to take care of your cover regularly!  - she will thank you with a good, fresh appearance and a long life! Tonno Tonic protects against harsh weather, cold winter and hot summer days. For care, simply spray Tonno Tonic on the previously cleaned tarpaulin. Wipe the surface dry with a clean cloth. Feel free to use Tonno Tonic to clean your tires - please wait 5 minutes after spraying before you can wipe the tire surface dry. Your rims will not be damaged. Tonno Tonic is available in a 0.47 liter spray bottle or as a 6-pack for dealers.

NOVISauto - pre-compressed, permanently elastic joint sealing tape  for sealing the joint between the hard top or load compartment cover and the vehicle load box. Seals reliably with joint widths between 4 mm and 9 mm when expanded. The foam rubber is placed on the cleaned bottom edge of the upright hard top / tonneau cover  glued on, previously trimmed a little at the ends.  Then the hard top / cargo area cover is carefully aligned on the upper edge of the vehicle cargo box and fixed using the existing aluminum clamps. A detailed assembly description is enclosed with the delivery.

NOVISAUTO pickup tailgate seal MAXSEAL for all common EU and US pickup vehicles: NOVISauto tailgate seal "MAX SEAL" keeps your pickup loading area free from dust, rain and snow - this EPDM sealing tape (ethylene propylene diene)  is a foil-shaped, synthetic rubber, a material according to DIN EN 13956 that is often used for roof and facade seals,  used for pond sealing.  The tailgate seal MAX - SEAL is up to 500% stretchable, permanently elastic (even at temperatures between -40 degrees Celsius and +120 degrees) and has a life expectancy of decades. The MAX - SEAL tailgate seals are resistant to aging and ozone without additional surface protection. They are UV and IR stable and resistant to a variety of chemical media.  (Source: from Wikipedia). Max Seal is easy to install in minutes using a do-it-yourself method - simply cut and glue the ends! - The band is long enough and suitable for  all pickup trucks with a tonneau cover or hard top. Equip your pickup with a tailgate seal from CARRYBOY / NOVISAUTO. This means that water and dust no longer have any chance of entering the pickup cargo area. The easy, quick and convenient way to seal your tailgate yourself.

NOVISauto - knee-friendly anti-slip mat, padded and insulated for workshop or garden work VERSATILE USE - Work mat for professional or DIY needs dimensionally stable, extremely hard-wearing and durable Generous foaming - therefore well padded and insulated towards the bottom Waterproof and quick drying Comfortable non-slip surface with coarse polypropylene needle felt (ideal for kneeling or lying down) Easily remove dirt with a garden hose or by knocking it out Practically stowed - folds in the middle Unfolded 60cm*120cm in size Ultra tough product made from 100% recyclable polypropylene  

NOVISauto – B-Light / B-Light  is the ultra-bright lighting for your pick-up loading area made of 8 brightly lit LED units, each with 6 LED bulbs. B-Light fits all pickup trucks and models - B-Light brightly illuminates the entire cargo area of your pickup - There is only one switch for the whole light system. B light is suitable for all pickups with any cargo area covers or hardtop.  To protect against slipping loads, B-Light should be mounted under the U-rail on the side.

NOVISauto - edge protection for the pickup tailgate of your Ford Ranger from year of construction 2012+ Effectively and inexpensively protect the scratch-prone upper edge of the tailgate of your 2010-2020 Ford Ranger! The NOVISAuto protective strip for the Ford Ranger tailgate offers long-lasting and very effective protection against scratches in the paintwork. Ideally suited if you already have a built-in loading space liner without edge protection or if the loading space is protected with a coating - because the edges of the loading area are still unprotected with both systems! The protective cap / rubbing strip for the Ford Ranger tailgate was developed for lasting protection against scratches, dents and dents. A close fit with smooth machined edges and durable plastic material make our Ford Ranger Edge Cover Moldings an excellent addition to your vehicle. The thickness of the edge protection is 3mm, up to 4mm in particularly stressed areas. The NOVISAuto Bushwacker protective strip is made of high-quality DURA-FLEX 2000 plastic. This plastic is very durable, impact and scratch-resistant and designed for all seasons. Harmful sun rays cannot harm your plastic edge protection, because the material does not fade. The surface is visually and haptically appealing with a slightly rough black surface.

Saddlebag -  Tool storage bag for all pick-up holds, soft material The ultra-practical storage bag for tools, sporting goods and lots of small items for the driver's side of your pick-up The Novisauto saddlebag has been specially made for each open-rail pick-up bed and is mounted on the rails of selected bed covers for maximum compatibility. Alternatively, the stowage bag can also be attached to the inside edge of the cargo area using clamps. With some vehicles (e.g. Nissan Navara) the lashing system can also be used to attach the tool storage bag if the loading sill is covered. The Saddlebag consists of two loading levels. The lower level features a zip closure and exterior pockets. Heavy-duty inserts ensure lasting strength and a tailored appearance. Lift, take off and take away  in a single operation, always and at hand on every occasion. You take the saddlebag with you to your workplace - together with all inserted tools and assembly parts! In the platform, you fix the storage box to save space on the side between the platform flap and the wheel housing.   

Equip your Ford Ranger extra cab (Spacecab), double cab or single cab (Singlecab) built in 2023+ with a CARRYBOY tailgate damper 111. Increase the usability of your pickup and increase comfort. With accessories from the Comfort & Ease of Use section. Ford Ranger accessories seamlessly adapt to your vehicle. Opt for a bespoke accessory that comes with a mounting kit and installation instructions. If you have any questions, you can contact us at any time. If you wish, we would be happy to professionally assemble the accessories for you. Take advantage of our strong CARRYBOY accessory model tailgate damper 111 from Carryboy for your Ford Ranger extra cab (Spacecab), double cab or single cab (single cab) built in 2023+. Your advantages summarized: for Ford Ranger extra cab/1.5 cab (Kingcab), double cab (Doublecab), single cab (Singlecab) year of construction from 2023+ CARRYBOY accessories manufactured by CARRYBOY Accessories designed for comfort & ease of use - black Mounting type: screws approximate assembly time: 10 min special feature: easy opening and high compatibility particularly suitable for: convenient use and simple application Attaches to tailgate and side Storage space approx. 0.5 m³ Our recommendation for your Ford Ranger Extra Cab (Spacecab), Double Cab, Single Cab (Singlecab) Our first-class CARRYBOY accessory tailgate damper 111 from Carryboy for your Ford Ranger 2023+ extra cabin (Spacecab), double cabin or single cabin (Singlecab) is suitable for every purpose! It is an ideal accessory for convenient use and easy application. Use the accessories for leisure and business! Best service - before and after the purchase You can rely on our service! Uncertainties or questions? Ask us by email or phone! We would be happy to advise you in detail and in a customer-oriented manner . Due to our daily work in the office AND warehouse, as well as our extensive wealth of experience thanks to 16 years of practical work, we are technically adept, technically competent and have practical experience. Are you concerned about sustainability or long-term use? No problem! The use of high-quality materials, raw materials and parts enables our accessories to have a long service life and useful life. Sustainability is achieved through lifelong use and thus the saving of resources for new production. More comfort and increased user-friendliness with CARRYBOY tailgate dampers 111 The accessory Carryboy tailgate damper 111 is delivered in black . The Carryboy CB-111-FT tailgate damper gas pressure spring is installed on the tailgate, on the side . The approximate installation time is 10 minutes on your Ford Ranger. Mounting with screws allows for better stability of the accessories. The accessory is particularly secure thanks to screws. The special features of the accessories are: easy opening and high compatibility . Convenient to use and easy to use : in summary, the CARRYBOY tailgate damper 111 accessory for your Ford Ranger extra cab/1.5 cab (Kingcab), double cab (Doublecab) or single cab (Singlecab) from 2023+ is particularly suitable for this.

NOVISauto - edge protection for the pick-up loading sill on the right and left of your Ford Ranger double cab from year of construction 2012+ Protect the scratch-prone upper edge of the loading area of your Ford Ranger double cab effectively and inexpensively. The NOVISAuto protective strips for the Ford Ranger sides offer long-lasting and very effective protection against scratches in the paintwork. Ideally suited if you already have a built-in cargo area liner without edge protection or the cargo area is protected with a coating - because the edges of the cargo area of your Ford Ranger are still unprotected with both systems! The protective cap for the Ford Ranger side loading sills was developed for lasting protection against scratches, dents and dents. A close fit with smooth machined edges and durable plastic material make our Ford Ranger Edge Cover Moldings an excellent addition to your vehicle. The thickness of the edge protection is 3mm, up to 4mm in particularly stressed areas. The NOVISAuto Bushwacker protective strip is made of high-quality DURA-FLEX 2000 plastic. This plastic is very durable, impact and scratch-resistant and designed for all seasons. Harmful sun rays cannot harm your plastic edge protection, because the material does not fade. The surface is visually and haptically appealing with a slightly rough black surface.

CARRYBOY - aluminum cross member elliptical shape for mounting on all CARRYBOY hardtops with roof rails Length of the crossbars 125 cm Sturdy aluminum with a satin finish Including rubber insert Including attachments (matching feet) for the hardtop roof rails Can be attached to the hardtop without drilling When ordering, please name the built-in hardtop / cargo area roller blind - model The crossbars are ideal for attaching the CARRYBOY roof baskets - available in 5 different sizes.

Our BEDMAT is the perfect alternative or addition to a tub. No more awkward kneeling on the hard tub - no more dreary rippled appearance like a standard tub - no more shifting of the load while driving. With BEDRUG for your Ford Ranger 2012+/2019+ you make the right choice. The BEDMAT for the Ranger double cabin is installed in minutes. Thanks to the Velcro fastener, the load compartment mat or carpet can be removed and installed in a very short time. The BEDMAT load compartment carpet for the Ford Ranger double cab pick-up truck is made of the same material as a "normal" standard tub. The load compartment mat is therefore just as easy to care for, robust and practical - thanks to its unique advantages it is even more practical than the standard liner. Custom-fitted to your pickup truck, the BEDMAT is resistant to a wide range of acids and stresses and is made from a single piece. Preserve and protect your load compartment liner and paintwork. The BEDMAT  can also be combined with a "standard" tub. Fits: Spray Tub/No Tub Tailgate part not included! --> order separately: Tailgate Installation with tub not possible --> can be ordered, if required, send us an e-mail

NOVISauto - bed mat model BedMat in universal size for all common and non-common pickup models (also for special editions, extended vehicles) The NOVISAuto anti-slip pickup floor mat for the loading area is a perfect addition to your pickup. The anti-slip mat from NOVISAuto not only impresses with its properties as a non-slip accessory for the loading area, but also as an instrument for visually enhancing your loading area. The Bedmat is an integrated system made of permanently stable and durable materials. The surface of the anti-slip mat is covered with a comfortable but easy-care artificial carpet. This carpet provides the anti-slip properties and can be kept clean with a high-pressure cleaner or a hand brush. The base of the anti-slip mat for your pickup is made from 100% recycled polypropylene. The material is foamed and applied in 3 separate layers. In combination with the carpet surface, this ensures a unique protection factor against chemicals, dust & dirt, impacts and point loads. The padding and underlay also make work on the loading area easier. The surface prevents objects that are transported on the loading area from slipping. The NOVISAuto Bedmat model can be universally installed in all pickup vehicles. Perforations for US - full-size pickups (e.g. Dodge RAM, Ford F150) are already in place. For other less common vehicles, the mat can easily be cut to size with a sharpened box cutter. The dimensions of 170cm width and 250cm length allow installation in almost all pickup - loading areas. It can be installed either on a cargo area liner, on a spray coating or on the bare surface of the cargo floor. Appropriate adhesive pads with Velcro are included in the delivery. Ideally suited for extra cab or singlecab pickups (Toyota Hilux singlecab, VW Amarok singlecab, Ford Ranger singlecab, Ford Ranger extra cab, Toyota Hilux extra cab, Nissan Navara extra cab, Isuzu D-Max extra cab) or individual loading area extensions (e.g. by the company Veeth in the Netherlands ). universally applicable for all models Dimensionally stable, extremely hard-wearing and durable - therefore the best protection against scratches and damage to the loading area Protection against negative environmental influences (e.g. chemicals, acids, rust, etc.) easy to assemble - no drilling required in the vehicle platform ideally suited for an exceptionally long service life stable and easy to use continuous fabric between loading area and tailgate against unwanted deposits Anti-slip surface for safe transport This is the most innovative and unique load compartment liner there is. You get the look and comfort of a rug in an ultra-tough 100% polypropylene product. Thus, your loading area is not only protected against impacts and damage, but the bed liner also withstands stresses from gravel to battery acid.  

NOVISauto – SwingCase for the Ford Ranger 2012+ / 2019+ pickup The ultra-practical box for tools, sporting goods and lots of small parts! You can reach your tools and small parts by effortlessly detaching your SwingCase box from the holder with just one movement and swiveling it towards you. No slouching or "bunk climbing"  is more needed! NOVISauto, the leader in selling popular Ford Ranger accessories, builds these multi-purpose storage boxes out of high-impact ABS hard plastic for your convenience - strong enough for a long Ranger pickup truck life. SwingCase is "tough", it is waterproof, space-saving and therefore ideally suited for your Ford Ranger in all loading lengths. - The purchase of two SwingCases for both sides of your Ford Ranger platform wall is the best choice - space-saving, absolutely tight and easy to handle! Raise, lift off and take with you in a single operation, always ready to hand on any occasion: You take the SwingCase with you to your construction site or workplace - together with all the packed tools and assembly parts!  SwingCase can be parked lying down or standing as usual. On the Ford Ranger 2012+, you can fix the SwingCase tool box on the side between the platform door and the wheel housing to save space. SwingCase for your Ford Ranger truck on the passenger side can be swung out and thus fills the previously unused platform space between the wheel housing and tailgate - adapted for every pickup of all vehicle manufacturers, models and years of construction. The box can be locked with a rotary lock and permanently locked with a key. SwingCase is made of tough and durable ABS rigid plastic, strong enough to hold a weight of up to 34kg. The tool box is resistant to UV radiation and does not fade. In addition, the tool box can be secured to the vehicle with a small padlock. This locking device is already included in many new swing case storage box series. The tool box (tool box) and storage box is an essential Ford Ranger accessory for every tradesman or hobby - do-it-yourselfers. Suitable for all Ford Ranger models (XL, XLT, Limited, Wildtrak, Raptor). The initial installation takes only about 15 minutes with 6 self-tapping sheet metal screws. Please note that the swing case cannot be installed in combination with an extendable loading floor. For Ford Ranger pickups with an inserted load compartment tub, this must be cut out in two places to ensure that the swing case tool box is held securely. This is the only way to ensure that the bracket fits perfectly on the vehicle.

Load compartment liner over edge for Mercedes X-Class double cab 2018-2020 dimensionally stable, extremely hard-wearing and durable - therefore the best protection against scratches and damage to the loading area Protection against negative environmental influences (e.g. chemicals, acids, rust, etc.) precisely fitting and easy to assemble - no drilling required in the vehicle platform Including screw points for original lashing rails on the sides of the loading area ideally suited for an exceptionally long service life stable and easy to use for a variety of commercial uses made of durable polyethylene (HDPE) Economical in daily use, as it protects the paintwork at low cost Made in the USA - no re-import from the Far East. Accesories Tailgate protection with edge protection included assembly description with the necessary mounting accessories

Cargo area liner for Ford Ranger Double Cab 2012+ Dimensionally stable, extremely hard-wearing and durable - therefore the best protection against scratches and damage to the loading area Optimum utilization of the loading area (less clumsy than the original Ranger tub - behind the tailgate directly on the side panel of the vehicle, therefore the maximum loading width is used) Protection against negative environmental influences (e.g. chemicals, acids, rust, etc.) precisely fitting and easy to assemble - no drilling required in the vehicle platform ideally suited for an exceptionally long service life including upper edge protection of the tailgate stable and easy to use for a variety of commercial uses made of durable polyethylene (HDPE) Economical in daily use, as it protects the paintwork at low cost Made in the USA - no re-import from the Far East! Accesories Tailgate protection with edge protection included assembly description with the necessary mounting accessories  

Item No. CB-550x CARRYBOY - roof basket made of stainless steel, light and very stable aluminum with matching crossbars Available in 4 different sizes and 2 colors (silver or black): CB-550x-00    100*100cm CB-550x-01    100*120cm CB-550x-02    100*160cm CB-550x-03    100*130cm   The luggage rack can be mounted on most cars, SUVs, VANs, pickups, trucks and Carryboy hardtops with suitable fasteners (self-assembly is possible). - No drilling required! - Dimensionally stable, unbreakable and resilient - easy to assemble - do it yourself - - available in different dimensions - secure supply of spare parts The roof basket is supplied with crossbars and can be attached to the roof rails using the mounting kit supplied. Appropriate fasteners (roof racks) are required for attachment to SUVs and pickup truck cabs. If you have any questions, please contact us by telephone on 02151-393593 or by e-mail at info@carryboy.de Please ask for delivery times for additional sizes.

NOVISauto - load compartment liner, non-slip model BedRug BFRRD12 for Ford Ranger Double Cab 2012+ dimensionally stable, extremely hard-wearing and durable - therefore the best protection against scratches and damage to the loading area Protection against negative environmental influences (e.g. chemicals, acids, rust, etc.) precisely fitting and easy to assemble - no drilling required in the vehicle platform ideally suited for an exceptionally long service life it is stable and easy to use continuous fabric-like PP plastic between loading area and tailgate, this effectively protects the hinges of the platform flap Anti-slip surface for safe transport  The innovative and unique BEDRUG load compartment liner made of 100% polypropylene not only protects against impact and damage, but also withstands stress from gravel to battery acid.  

Item No. CB-550x CARRYBOY - roof basket made of stainless steel, light and very stable aluminum with matching crossbars Available in 4 different sizes and 2 colors (silver or black): CB-550x-00    100*100cm CB-550x-01    100*120cm CB-550x-02    100*160cm CB-550x-03    100*130cm   The luggage rack can be mounted on most cars, SUVs, VANs, pickups, trucks and Carryboy hardtops with suitable fasteners (self-assembly is possible). - No drilling required! - Dimensionally stable, unbreakable and resilient - easy to assemble - do it yourself - - available in different dimensions - secure supply of spare parts The roof basket is supplied with crossbars and can be attached to the roof rails using the mounting kit supplied. Appropriate fasteners (roof racks) are required for attachment to SUVs and pickup truck cabs. If you have any questions, please contact us by telephone on 02151-393593 or by e-mail at info@carryboy.de Please ask for delivery times for additional sizes.

NOVISauto sport bar roll bar 2.0 Black Edition for your EU pickup (Ford Ranger 2012+, Nissan Navara 2016+, Renault Alaskan, Mercedes X-Class, Isuzu D-Max 2012+/2020+, Toyota Hilux) Give your pickup style and a massive appearance with the roll bar sport bar 2.0 in matt black design. The roll bar sport bar 2.0 does not block your 3.  Brake light - It remains visible for everyone. This universal version was developed for the entire range of common pickups in Germany. Make your pickup unique with this roll bar. The following vehicles can be equipped with the roll bar: Ford Ranger 2012+ Nissan Navara NP300 2016+ Isuzu Dmax 2012- 2020 / 2020+ Renault Alaskan 2017+ Mercedes X Class 2018-2020 Toyota Hilux 2016+ /2021+ The roll bar 2.0  is compatible with most retractable or roll-up tonneau covers  and various covers for folding.  The fixed standard version of the roll bar can be equipped with lighting panels including a variety of individual lights and LED strips up to a length of  101 cm (40 inches) can be equipped. Alternatively, an electrically operated holder allows the lights to be lowered using a switch when not in use. The sports hanger 2.0 is made of steel, dimensionally stable, unbreakable and resilient. You get the best quality in terms of workmanship and design. The matt black powder coating of the roll bar protects the material and ensures a coordinated look. The delivery includes assembly kit and installation instructions, the assembly time is about 2 hours. Note: Drilling holes on your pickup are required for assembly if you want to combine certain load compartment covers. We recommend the use of rivet nuts in this case. On vehicles without tonneau covers, the bracket can be installed using convenient mounting clips.

Carryboy - full bed pull-out shelf  -  Pull-out shelf cut out of aluminum checker plate according to the contour of the wheel housing This extendable loading floor is also available in combination with a drawer system in different sizes (CB-800). - Load capacity up to 350 kg! - Easy loading and unloading - you save time with it! - Non-slip, hard-wearing, easy-to-clean loading surface made of aluminum checker plate - best quality in processing and design - dimensionally stable, unbreakable and loadable up to approx. 350 kg - secure supply of spare parts - Simple assembly according to video and written assembly instructions - Convenient securing of the load with the integrated lashing eyes - The ball-bearing loading floor is unlocked with the handle - The loading area is almost completely filled - Wheel housings are cut out A notice:  these products are so-called selection products, which are individually manufactured to your order. This pull-out drawer is divided into S / M / L categories in terms of dimensions. Due to the rectangular shape, the loading floor fits on different vehicles. As an option, the loading floor can be fully adapted to the vehicle. The area of the accessory drawer is expanded to include the area behind the wheel arches. When ordering, please indicate the vehicle in question so that we can assign you the right vehicle. You can also choose between the pull-out loading floor in aluminum or covered with an anti-slip rubber coating.

Equip your Ford Ranger 2023+, Isuzu D-Max 2021+ with a CARRYBOY 778 loading floor extension. Expand and protect your storage space for everyday use. With accessories from the stowage & transport solutions section. Our accessories for your Ford Ranger 2023+, Isuzu D-Max 2021+ Double cab (Doublecab) built up to 2022 adapts seamlessly to your vehicle. Mounting kit and installation instructions are included. If necessary, you can watch our assembly videos on Youtube. If you have any questions, you can contact us at any time. Have your accessories assembled by our technically experienced, professionally competent and practically experienced employees on request! Benefit from our strong Carryboy accessory model 778 loading floor extension for your Ford Ranger 2023+, Isuzu D-Max 2021+ double cabin. More space, more fun - loading floor pull-out 778 from CARRYBOY as ideal storage and transport solutions The accessory model "Load floor pull-out 778" from CARRYBOY for your Ford Ranger 2023+, Isuzu D-Max 2021+ double cab is particularly UV-resistant . This increases the life of the accessory - it is protected from the sun and fading. The durable accessory loading floor pull-out 778 from CARRYBOY is particularly scratch-resistant . A long use in top condition without major signs of use is made possible. Load your truck from the sides or the back. Our accessories do not block your access . The CARRYBOY 778 loading floor extension accessory is made of steel and aluminum for your Ford Ranger 2023+, Isuzu D-Max 2021+ double cab. Low weight, robustness, stability and durability are the special properties of aluminium . Among other things, the accessory uses loading floor extension 778 for your Ford Ranger 2023+, Isuzu D-Max 2021+ aluminum for this reason. The advantages of steel cannot be denied. Steel is strong, resilient and stable. This means that your accessories are well prepared for loads. Accessories Carryboy loading floor pull-out 778 is impact-resistant and thus offers effective protection against sudden loads. The loading floor pull-out accessory 778 can withstand 350 kg . The CARRYBOY loading floor pull-out rectangular 350kg is installed on the flatbed . You will need approximately 1-3 hours to fit the cover on your Ford Ranger 2023+, Isuzu D-Max 2021+. The assembly takes place without drilling. The loading floor pull-out is attached to the platform edge to ensure stability. The special features of the accessories are: easy to open, robust, versatile, extendable and easy to clean . In summary, the CARRYBOY 778 loading floor extension accessory is for your Ford Ranger 2023+, Isuzu D-Max 2021+ double cab particularly suitable for: trade, daily use, comfortable use, extreme stress, frequent use, simple use and professionals . The entire equipment at a glance: for Ford Ranger 2023+, Isuzu D-Max 2021+Double Cab CARRYBOY accessories manufactured by CARRYBOY Accessories suitable for storage & transport solutions particularly UV-resistant scratch resistant Loading area fully accessible Type of installation: without drilling Material: steel and aluminum approximate assembly time: 1-3 h particularly shockproof: yes Load capacity: 350 kg special feature: easy to open, robust, versatile, extendable and easy to clean particularly suitable for: trade, daily use, comfortable use, extreme stress, frequent use, simple use and professionals Our recommendation for your pickup truck Our first-class CARRYBOY accessory loading floor pull-out 778 from Carryboy for your Ford Ranger 2023+, Isuzu D-Max 2021+ Double cab is suitable for every purpose! It is an ideal accessory for commercial, daily use, convenient use, heavy duty use, frequent use, easy use and professional. Use the accessories for leisure and business! Our service to you - before and after the purchase Rely on our service! uncertainties? Questions? Contact us by email or phone! We would be happy to advise you in detail and in a customer-oriented manner . Due to our daily work in the office AND warehouse, as well as our extensive wealth of experience thanks to 16 years of practical work, we are technically adept, technically competent and have practical experience. Is long-term use and thus sustainability important to you? No problem! A long service life and useful life of our accessories is made possible by the use of high-quality parts, raw materials and materials. Sustainability is achieved through lifelong use and thus the saving of resources for new production.

CARRYBOY ROOF TENT CB-102-2P for all common pickups, SUVs and mid-size cars: Material:   Materials from the outside:   Oxford polyester with silver coating and UPF50+ (absorbs more than 98% of UV rays)   Material from inside:   190 g/sqm rip-stop polyester with PU 2000mm   Bottom material:          210 Denier Oxford Nylon with PU 2000mm Interior:   rust-free aluminum struts ensure structure and comfortable lying   6 cm foam mattress can be removed and cleaned    6 large windows with insect screens   2 shoe bags at the entrance - the dirt stays outside Comfort: Self-deploying within a few seconds using gas pressure springs spacious room for 2-3 people Protected against wind, weather and rain Foam mattress 6cm 2 extra shoe boxes Entry ladder can be extended by a maximum of 2m, fixed to the tent and foldable Fly screens in front of the windows Reliable UV protection tent size:   Unfolded & erected:           1,340 x 2,165 x 1,343mm   folded:             1,340 x 2,165 x 300mm   Weight:                               56 kg (together with ladder)    

Novisauto Pathfinder-1 roof tent The Novisauto roof tent for every pickup or at least mid-range SUV is one of the first innovative electrically controllable roof tents. You can straighten it up and down with a simple push of a button, alternatively you can also do it by hand. The tent is set up on the vehicle using clamps on cross members. Comfort : Self-erecting by remote control within 60 seconds Power supply via socket of the vehicle (3m cable) spacious interior with enough space for 2 people Reliable protection against wind and rain with extendable telescopic aluminum ladder - loadable up to 150kg with 6cm foam mattress. The cotton cover can be removed and washed. 2 extra hanging pockets for storing shoes, for example double fly screens in front of the windows and the entrance Tent size :   unfolded & erected (inside):      1,200(W) x 2,000(L) x 1,100(H) mm   Weight:                                       56 kg (together with ladder)   Material :   Material outside:   Oxford polyester with silver coating and UPF50+ *   Materials inside:   190 g/sqm ripstop polyester with 2000 mm water column   Bottom material:   210 Denier Oxford Nylon with 2000mm hydrostatic head Interior :   Stainless steel struts provide structure.   6 cm foam mattress can be removed with cover   6 windows with insect screen and privacy screen   2 additional shoe bags  

Carryboy - Slide Floor Universal  -  Pull-out shelf made of aluminum checker plate with a three-sided frame for all mid-size pickup trucks This extendable loading floor is also available in combination with a drawer system in different sizes (CB-800). - Load capacity up to 350 kg! - Easy loading and unloading - you save time with it! - Non-slip, hard-wearing, easy-to-clean loading surface made of aluminum checker plate - best quality in processing and design - dimensionally stable, unbreakable and loadable up to approx. 350 kg - secure supply of spare parts - Simple assembly according to video and written assembly instructions - Convenient securing of the load with the integrated lashing eyes - The ball-bearing loading floor is unlocked with the handle. A notice:  these products are so-called selection products, which are individually manufactured to your order. This pull-out drawer is divided into S / M / L categories in terms of dimensions. Due to the rectangular shape, the loading floor fits on different vehicles. As an option, the loading floor can be fully adapted to the vehicle. The area of the accessory drawer is expanded to include the area behind the wheel arches. The universal loading floor CB-778 is available as an accessory for these pickup vehicles with the following dimensions: Size S (1020*1380*208) - Toyota Hilux Revo, Isuzu Dmax, Mitsubishi L200, Fiat Fullback Size M (1080*1380*208) - Ford Ranger, Nissan Navara NP300, Renault Alaskan Size L (1200*1440*208) - VW Amarok Size XL - with the appropriate width, but 1700 mm length for single and extracab pickups. When ordering, please indicate the vehicle in question so that we can assign you the right vehicle. You can also choose between the pull-out loading floor in aluminum or covered with an anti-slip rubber coating.